Our Top Picks
Culligan RFC-BBSA Whole House Water Filter10" x 4.5" (Pack of 1)4.5 x 4.5 x 9.75 inches1.9 poundsCheck on Amazon
Culligan R50-BBSA Whole House Water FilterR50-BBSA Filter4.3 x 4.3 x 9.9 inches0.55 poundsCheck on Amazon
Culligan CW5-BBS Whole House Water Filter1 Count (Pack of 1)4.5 x 4.5 x 10 inches1.5 poundsCheck on Amazon
To size a whole house water filter, match its rated flow in gallons per minute (GPM) to your peak household demand, then pick a micron rating that fits the problem in your water: about 5 micron for general sediment, 1 micron or lower for fine silt, and carbon stages for chlorine, taste and odor. Many homes land somewhere between about 7 and 15 GPM depending on bathrooms and fixtures, and larger or well-water homes often need more. This guide walks through the arithmetic, the micron choices, cartridge costs and the pressure drop that most listings do not mention.
Key takeaways
- Size by peak flow, not by number of people: add up fixtures that can run at the same time, then choose a filter rated above that number.
- Micron rating describes the size of particles a cartridge catches. Lower is finer, but finer cartridges clog sooner and restrict flow more.
- Carbon cartridges handle chlorine, taste and odor; they are not a sediment filter and do not remove everything. Check the certifications on the listing.
- Budget for cartridge replacements and plan for some pressure drop, especially once a filter is half loaded.
Step 1: Work out your peak flow in GPM
Whole-house filters sit where water enters the building, so everything you run at the same time passes through them. The rated flow on the box should be higher than your peak demand, not equal to it. A filter pushed to its limit loses pressure and wears cartridges quickly.

Culligan P5 Whole House Water Filter, 10 x 2.5 in, 5 Micron, 4-Pack | IAPMO Certified | Best For Extra Fine Silt & Sediment | 2 Months / 8,000 Gal | Fits HF-360A, WH-S200-C & HF-150A
Chosen because it specifies 10 x 2.5 in and 5 Micron.
View on Amazon
Culligan RFC-BBSA Whole House Water Filter, 10 x 4.5 in, 25 Micron Carbon | IAPMO Certified | Best For Silt, Fine Sand & Chlorine Taste | 3 Months / 10,000 Gal | 3 GPM | Fits WH-HD200-C & HD-950A
Chosen because it specifies 10 x 4.5 in and 25 Micron Carbon.
View on Amazon
Culligan R50-BBSA Whole House Water Filter, 10 x 4.5 in, 50 Micron Coarse | IAPMO Certified | Best For Coarse Sediment, Rust & Scale | 6 Months / 24,000 Gal | 10 GPM | Fits WH-HD200-C & HD-950A
Chosen because it specifies 10 x 4.5 in and 50 Micron Coarse.
View on Amazon
Culligan CW5-BBS Whole House Water Filter, 10 x 4.5 in, 5 Micron Extra Fine | IAPMO Certified | Best For Fine Silt & Sediment | 4 Months / 16,000 Gal | 8 GPM | Fits WH-HD200-C & HD-950A
Chosen because it specifies 10 x 4.5 in and 5 Micron Extra Fine.
View on Amazon| Fixture | Typical flow (GPM) |
|---|---|
| Bathroom sink | 1.0 to 1.5 |
| Kitchen sink | 1.5 to 2.2 |
| Shower | 1.8 to 2.5 |
| Dishwasher | 1.0 to 2.0 |
| Washing machine | 2.0 to 3.0 |
| Toilet refill | 1.5 to 3.0 |
| Outdoor hose bib | 5.0 or more |
These are common ranges; check your own fixtures’ labels. Now count what could run together. A busy morning might be two showers (about 4 to 5 GPM), the kitchen sink (2) and a washing machine (3), for a peak near 10. That sets a floor of 10 GPM for the filter’s service flow. Add a margin and you land at 12 to 15 GPM.
Rule-of-thumb sizing by home
| Home type | Bathrooms | Suggested rated flow | Notes |
|---|---|---|---|
| Apartment or small house | 1 | 6 to 8 GPM | Smaller 10-inch housings may be enough |
| Typical family home | 2 to 3 | 10 to 15 GPM | Often a 20-inch or Big Blue-style housing |
| Large home | 4 or more | 15 to 20 GPM or more | Consider parallel housings or larger-diameter tanks |
| Well water with irrigation | Any | Match pump output | Check pump GPM and pressure tank before sizing |
These are starting points, not guarantees. The maker’s flow figure may be a maximum rather than a service flow at your pressure. Read the footnotes on the listing and compare the stated pressure drop at that flow.
Step 2: Choose the micron rating for the job
A micron is one-millionth of a meter. A sediment cartridge rated at 5 microns is built to catch particles about that size and larger. A 1-micron cartridge catches finer silt but also loads faster. Most whole-house systems stage the filtration from coarse to fine so that the fine cartridge is not overwhelmed.
| Micron rating | Typical use | Flow and clogging effect |
|---|---|---|
| 50 micron | Coarse sand and rust flakes on well water | Very low restriction, short protection only |
| 20 micron | Visible silt, pre-filter for finer stages | Low restriction |
| 5 micron | General city or well sediment, common first stage | Balanced; a popular default |
| 1 micron | Fine silt, cloudy water | Higher restriction, change more often |
| 0.5 micron | Very fine particles, polishing stage after a coarser filter | Highest restriction; needs a pre-filter in front |
A micron rating alone does not tell you about chemicals. Chlorine and chloramine, lead and other dissolved substances need other media: carbon block, KDF, catalytic carbon or specialty resins. Chloramine in particular is usually handled with catalytic carbon rather than standard granular carbon, and a nominal 5-micron sediment cartridge should not be assumed to remove cysts or other microbes. Whole-house systems with NSF/ANSI certification are uncommon and are often certified at lower flow than the marketed rating, so read the certification details for the exact flow and claim. Look for third-party certification such as NSF/ANSI standards on the exact claims you care about, and read what contaminants and flow rates the certification actually covers.
Whole house water filters: stage types and what each does
- Sediment stage. Spun polypropylene or pleated cartridges that trap sand, rust and silt. Usually first in line.
- Carbon stage. Granular or block carbon that reduces chlorine, taste and odor. A block has more contact time but may restrict flow more than granular.
- Specialty stage. KDF, anti-scale or heavy-metal media. Listings mention these for some systems; check the maker page for what they claim and how long the media lasts.
- Self-cleaning or auto-flush sediment. Some systems backwash the sediment screen to avoid frequent cartridge changes. They cost more upfront.
- Whole-house tank systems. Larger tanks with media beds and control heads, a different category with higher flow and lower pressure drop but more plumbing work.
Step 3: Account for pressure drop
Every filter adds resistance. The figure to find on the spec sheet is the pressure drop (in psi) at a stated flow rate when the cartridges are clean. A typical clean filter may drop only a few psi at its service flow, and the loss grows as cartridges load with sediment. A finer micron, a tighter carbon block and a smaller housing all increase the drop.
What this means in practice: if your incoming pressure is 40 psi, a loss of 10 psi can be noticeable in the shower. If it is 70 psi, you may never notice. Measure your incoming pressure with an inexpensive hose-bib gauge before you buy. If the number is low, favor larger housings, coarser final micron ratings or a bigger diameter system, and set a changing schedule that keeps cartridges from loading too far.
Step 4: Budget cartridge replacement
| Cartridge | Typical interval | What shortens it |
|---|---|---|
| Sediment, 5 micron | 3 to 6 months | Well water, construction nearby, old pipes |
| Carbon block | 6 to 12 months | High chlorine, hot-water draw, very large households |
| Specialty media | Varies; see maker’s gallon rating | Hard water, high contaminant load |
| Self-cleaning sediment screen | Periodic flush; replace screen per manual | Silt-heavy supply |
Intervals depend on your water. Many makers rate cartridges by gallons rather than months, so convert: a family using 300 gallons a day goes through about 9,000 gallons in a month. A cartridge rated at 100,000 gallons would, on paper, last about eleven months, but sediment can clog it earlier. Watch the pressure gauge on the housing, if there is one, and change when the drop becomes noticeable. Cost per year is the sum of the cartridges you change times their price, so ask what a full set costs before you buy the system.
Models that show up for this search
These listings are examples of how the sizing terms appear in practice. Details come from listing text; check the maker page for the current model, flow and certification before buying.
Gear that helps
- A. O. Smith Whole House Water Filter System (AO-WH-Filter) · 600K gallon rating · 6-year filter · NSF-certified · 14 GPM per listing.
- Waterdrop WHF3T-PG 3-Stage Whole House Water Filter System · 5 micron · multi-stage for sediment and chlorine, taste and odor per listing.
- iSpring WGB32B Whole House Water Filter System · 3-stage · sediment, taste and odor stages per listing; a Big Blue-style layout.
- HQUA WF3-01 3-Stage Whole House Water Filtration System · heavy-metal reduction claims on the listing; verify the certification details.
Installation and planning checklist
- Find the main shut-off. Locate where water enters the house and confirm the valve works before you plan the install.
- Measure pipe size. Most systems use 3/4-inch or 1-inch ports. Match your pipe to the housing ports or plan adapters.
- Measure space. A 20-inch housing needs about a foot of clearance below for cartridge changes. Allow room on the wall for three housings in a row.
- Decide on a bypass. A three-valve bypass lets you isolate the filter for service without shutting off water to the house.
- Add a pressure gauge. A gauge before and after the filter makes the pressure drop visible and tells you when to change.
- Plan for a leak check. Open the supply slowly, bleed air from the housings and check every joint after an hour and again after a day.
- Consider a pro. If you are not comfortable cutting or soldering pipe, push-fit fittings or a licensed plumber are safer. Follow local plumbing codes and the maker’s manual.
- Know your water. A recent municipal water quality report or a lab test on well water tells you what you need to treat, so you do not buy stages you do not need.
Match the filter to your water
| Your water problem | What to look for | Sizing note |
|---|---|---|
| Chlorine taste and smell (city water) | Carbon stage, sediment pre-filter | Flow headroom matters for hot showers and laundry |
| Sand, rust or cloudy water (well) | Coarse to fine sediment, 20 then 5 micron | Plan for frequent cartridge changes or auto-flush |
| Hard water scale | A water softener or scale-prevention media; filters alone do not soften | Do not confuse anti-scale with softening; read what is claimed |
| Iron or sulfur smell | Specialty media or a dedicated iron system | Often needs a tank-style system and professional advice |
| Concern about lead or metals | Verified certification for those contaminants | Also consider a point-of-use drinking water filter |
FAQ
What flow rate do I need for a whole house water filter?
Add up the fixtures that can run at once. Estimates vary by source, but many one- to three-bathroom homes land somewhere between roughly 7 and 15 GPM. Choose a model with a rated flow above that number, and read the stated pressure drop at that flow.
What micron rating is best for a whole house filter?
Five micron is a common general-purpose choice. Use 20 micron or coarser ahead of it for sandy well water, and use 1 micron or finer only after a coarser stage so it does not clog quickly.
Will a whole house filter reduce my water pressure?
Slightly, yes. Clean filters usually cost a few psi; loaded cartridges cost more. Larger housings, coarser micron ratings and regular cartridge changes keep the loss small.
How often should I change the cartridges?
Sediment cartridges commonly need changing every three to six months, and carbon every six to twelve, but your water decides. Change sooner if pressure drops or water tastes off, and follow the maker’s gallon rating.
Does a whole house filter remove everything?
No. It reduces what its media is designed for. Check the certifications for each claim, and consider a separate drinking-water filter if you have specific health concerns.
Can a whole house filter soften water?
No. Standard filters do not remove hardness minerals. A softener or a different scale-control system is needed for that.
Do I need a plumber to install one?
Not always. With push-fit connections and basic tools, many homeowners can install one. If you need to cut copper, work with an old main or deal with a well system, a plumber is a safer choice.
Putting the numbers together
Start by listing the fixtures that run together at your busiest hour and adding their GPM; that is your peak flow. Pick a system rated above it. Choose a 5-micron sediment stage as the default, a coarser pre-filter if your water carries sand, and carbon for chlorine and taste. Measure incoming pressure, read the pressure drop at your flow, and price a full year of cartridges before you commit. A filter that is slightly oversized and changed on schedule will serve you better than a tight fit that loads up and starves the shower.
Last updated: November 2026.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Collect the home and kitchen items you want in one registry that guests can shop from.
Create a wedding registrySet up recurring deliveries of everyday items on eligible products. Terms and savings are set by Amazon.
Explore Subscribe & SaveFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.